Activate VW Lane Assist Memory Function: Step-by-Step Guide

Table of Contents

1. Introduction
2. Understanding the Issue with Lane Assist
3. The Solution: Activating the Lane Assist Memory Function
4. Step-by-Step Instructions for Golf A
   • Starting the Car
   • Activating Lane Assist
   • Deactivating Lane Assist
   • Shutting Down the Engine
5. Compatibility with Other Vehicles
6. Alternatives to VCDs for Coding
7. Seek Professional Help
8. Conclusion
9. References

Activating the Memory Function for Lane Assist

Lane assist is a popular feature in modern vehicles that helps drivers stay in their lanes and provides an added layer of safety. However, some drivers find the constant activation of lane assist to be inconvenient, especially in areas where it may not be necessary. In this article, we will discuss how to activate the memory function for lane assist, allowing it to remember your last setting and eliminating the need to repeatedly activate or deactivate it.

Introduction

Lane assist is a driver assistance system that uses cameras and sensors to monitor the vehicle's position within the traffic lanes. It provides visual and auditory feedback to alert drivers if they unintentionally veer out of their lane. While this feature is undoubtedly beneficial, some drivers may find it bothersome to manually activate or deactivate lane assist each time they start their vehicle.

Understanding the Issue with Lane Assist

For drivers who frequently drive in areas where lane assist is unnecessary, such as private properties or roads without marked lanes, the constant activation of lane assist can be frustrating. This inconvenience has led many drivers to seek a solution that allows them to have more control over the lane assist feature.

The Solution: Activating the Lane Assist Memory Function

The memory function for lane assist is a feature that enables the vehicle to remember the last setting of the lane assist feature. By activating this function, drivers can have their preferred lane assist setting automatically applied each time they start the vehicle, eliminating the need for repetitive manual adjustments.

To activate the lane assist memory function, you will need to follow a simple coding process using VCDs (VAG-COM Diagnostic System). This process involves accessing the A5 Front Sensor Driver Assist module and modifying the coding in Byte9. It is essential to ensure that you have the most up-to-date version of VCDs before proceeding with the coding process.

Step-by-Step Instructions for Golf A

1. Start the Car:

   • Begin by starting the vehicle's engine and allowing it to run properly.

2. Activating Lane Assist:

   • Locate the Lane Assist button, typically found on the vehicle's control panel.
   • Press the Lane Assist button to activate it.
   • A prompt will appear on the display confirming the activation.
   • Press the OK button to complete the activation process.

3. Deactivating Lane Assist:

   • To deactivate lane assist, simply uncheck the Lane Assist button.
   • The button will disappear from the display, indicating that lane assist is deactivated.

4. Shutting Down the Engine:

   • Turn off the vehicle's engine.
   • Open and close the doors to allow for a quick shutdown process.

5. Reactivating Lane Assist:

   • Start the vehicle's engine again.
   • Give the system a few seconds to initialize.
   • Press the Lane Assist button to reactivate it.
   • The system should remember the last state it was left in before the engine shutdown.

By following these steps, you can enable the lane assist memory function in Golf A, ensuring that the system remembers your preferred setting each time you start the vehicle.

Compatibility with Other Vehicles

While the coding process described above is specifically demonstrated on a Golf A, it is worth noting that similar procedures can be applied to other vehicles that have the lane assist function. However, it is important to keep in mind that the coding may vary slightly between different vehicle models. We recommend consulting a professional or referring to the user manual of your specific vehicle for accurate coding instructions.

Alternatives to VCDs for Coding

If you are not familiar with VCDs or coding, there are alternative options available to activate the lane assist memory function. OBD-II diagnostic tools and software, such as OBD11 and Carista, offer similar functionality and user-friendly interfaces that can guide you through the coding process.

Seek Professional Help

If you are not confident in performing the coding process yourself or would prefer professional assistance, it is recommended to seek help from a qualified technician or an authorized service center. They have the expertise and tools necessary to activate the lane assist memory function accurately and efficiently.

Conclusion

The memory function for lane assist is a valuable feature that enhances the convenience of using lane assist in vehicles. By activating this function, drivers can have their preferred lane assist setting automatically applied each time they start the vehicle, eliminating the need for repetitive manual adjustments. Whether you choose to perform the coding yourself or seek professional help, the lane assist memory function can greatly improve your driving experience.

References

• Audi Upgrades: Website