Improve Cutting Performance with Adjusted Clipper Tension
Table of Contents
- Introduction
- Reasons for Patchy Cutting
- Understanding Clipper Tension
- Adjusting Clipper Tension for Better Performance
- Step 1: Loosen the Screws
- Step 2: Creating Tension
- Step 3: Retightening the Armature
- Step 4: Increasing Power
- Putting the Adjusted Clipper to the Test
- Conclusion
- Pros and Cons of Adjusting Clipper Tension
- Frequently Asked Questions (FAQs)
- Resources
📰 Article: How to Adjust Clipper Tension for Better Performance
Are you frustrated with wall seniors that pull your client's hair and cut in a patchy fashion? Don't worry, there's a solution! One of the main reasons behind this issue is the tension of the clipper's blade. In this article, we will explore the importance of clipper tension and guide you through the process of adjusting it for better performance.
Understanding Clipper Tension
Before we dive into the adjustment process, let's understand what clipper tension means. Tension refers to how tightly squeezed together the cutting blade and the comb blade are. If the tension is too low, hair can get between the blades and impair the cutting process. On the other hand, if the tension is too tight, the blades won't be able to move properly.
Reasons for Patchy Cutting
When experiencing patchy cutting with your clippers, there could be several reasons contributing to the issue. Slanted blades, lack of power, and inadequate oiling are common culprits. It's important to check all these factors and eliminate them as potential causes before adjusting the tension.
Adjusting Clipper Tension for Better Performance
To enhance the performance of your clipper, follow these steps to adjust the tension:
-
Step 1: Loosen the Screws
Start by undoing the three screws that allow access to the interior of the clipper. Use a corrugated rubber mat to prevent losing any screws during the process.
-
Step 2: Creating Tension
Locate the special star or torque screws on the side of the clipper. Loosen them by turning them clockwise with the appropriate attachment. This will allow you to adjust the tension.
-
Step 3: Retightening the Armature
Push down on the right-hand side of the armature, exerting approximately two pounds of pressure. Imagine the armature as a scale, and adjust the pressure accordingly. While holding it down, tighten the screws back up, ensuring a firm but not overly tight grip.
-
Step 4: Increasing Power
To maximize the power of your clipper, adjust the power screw. By bringing the armature closer to the motor, you'll achieve greater cutting power. Be cautious not to overdo it, as excessive power can lead to issues. Find the optimal power point and lock it in.
Putting the Adjusted Clipper to the Test
After adjusting the tension and power of your clipper, it's time to put it to the test. Cut through a sample of hair and observe the improved performance. The clipper should glide smoothly, without tugging or pulling. Enjoy the satisfaction of a clean and precise cutting experience.
Conclusion
Adjusting clipper tension is a simple yet effective way to improve its cutting performance. By understanding the importance of tension and following the adjustment steps outlined in this article, you can say goodbye to patchy cutting and enhance the quality of your work.
Pros and Cons of Adjusting Clipper Tension
Pros:
- Improved cutting performance
- Better control and precision
- Elimination of patchy cutting
- Enhanced client satisfaction
Cons:
- Incorrect adjustment may lead to blade malfunction
- Over-tightening can restrict blade movement
Frequently Asked Questions (FAQs)
Q: How often should I adjust clipper tension?
A: It is recommended to check and adjust clipper tension every few months or whenever you notice a decline in cutting performance.
Q: Can any type of clipper be adjusted for tension?
A: Yes, most clippers have tension adjustment features, but the specific process may vary. Consult the manufacturer's instructions for your clipper model.
Q: Is it necessary to oil the clipper blades regularly?
A: Yes, regular oiling is essential to maintain the smooth operation of the blades and reduce friction. Refer to the manufacturer's guidelines for the recommended frequency of oiling.
Q: Can adjusting clipper tension cause damage to the motor?
A: When done correctly, adjusting clipper tension should not damage the motor. However, it is essential to follow the recommended pressure and use caution during the adjustment process.
Resources
